BS EN 1055 1996
|
ID： |
BE3D13E309344B82AB8B0DC2B306E6FF |
|
文件大小(MB)： |
0.09 |
|
页数： |
14 |
|
文件格式： |
|
|
日期： |
2013-7-8 |
|
购买： |
文本摘录（文本识别可能有误，但文件阅览显示及打印正常，pdf文件可进行文字搜索定位）：
BRITISH STANDARD BS EN,1055 : 1996,BS 2782 :,Part 11 :,Method 1111A :,1996,The European Standard EN 1055 : 1996 has the status of a British Standard,ICS 23.040.20,NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW,Plastics piping systems D,Thermoplastics piping systems,for soil and waste discharge,inside buildings D,Test method for resistance to,elevated temperature cycling,Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Sun Oct 22 00:54:48 GMT+00:00 2006, Uncontrolled Copy, (c) BSI,This British Standard, having,been prepared under the,direction of the Sector Board for,Materials and Chemicals, was,published under the authority of,the Standards Board and comes,into effect on,15 September 1996,ó BSI 1996,The following BSI references,relate to the work on this,standard:,Committee reference PRI/61,Draft for comment 94/305478 DC,ISBN 0 580 25875 0,BS EN 1055 : 1996,Amendments issued since publication,Amd. No. Date Text affected,Committees responsible for this,British Standard,The preparation of this British Standard was entrusted to Technical Committee,PRI/61, Plastics piping systems and components, upon which the following bodies,were represented:,British Gas plc,British Plastics Federation,British Plumbing Fittings Manufacturers' Association,British Valve and Actuator Manufacturers' Association,Department of the Environment (British Board of Agre?ment),Department of the Environment (Building Research Establishment),Department of the Environment (Property and Buildings Directorate),Department of Transport,Electricity Association,Federation of Civil Engineering Contractors,Health and Safety Executive,Institute of Building Control,Institute of Materials,Institution of Civil Engineers,Institution of Gas Engineers,Institution of Water and Environmental Management,National Association of Plumbing, Heating and Mechanical Services Contractors,Pipeline Industries Guild,Plastics Land Drainage Manufacturers' Association,Society of British Gas Industries,Society of British Water Industries,Water Companies Association,Water Services Association of England and Wales,The following bodies were also represented in the drafting of the standard, through,subcommittees and panels:,ERA Technology Ltd.,Engineering Equipment and Materials Users' Association,RAPRA Technology Ltd.,Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Sun Oct 22 00:54:48 GMT+00:00 2006, Uncontrolled Copy, (c) BSI,BS EN 1055 : 1996,i,Contents,Page,Committees responsible Inside front cover,National foreword ii,Foreword 2,Method,1 Scope 3,2 Normative references 3,3 Definitions and symbols 3,4 Principle 3,5 Apparatus 3,6 Test assembly 6,7 Procedure 7,8 Test report 7,Figures,1 Typical test assembly for elevated temperature cycling test (1500 cycles),for piping systems inside buildings (application area `B' only) 4,2 Typical test assembly for elevated temperature cycling test (1500 cycles),for piping systems buried in the ground within the building structure,(application areas `BD' and `UD') 5,3 Typical test assembly for elevated temperature cycling test (1500 cycles),for piping systems with components with nominal outside diameter dn,smaller than 40 mm for use inside buildings (application area `B') 6,Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Sun Oct 22 00:54:48 GMT+00:00 2006, Uncontrolled Copy, (c) BSI,ii,BS EN 1055 : 1996,National foreword,This British Standard has been prepared by Technical Committee PRI/61 and is the,English language version of EN 1055 : 1996 Plastics piping systemsD Thermoplastics,piping systems for soil and waste discharge inside buildingsD Test method for,resistance to elevated temperature cycling, published by the European Committee for,Standardization (CEN).,It is incorporated into BS 2782 Methods of testing plastics : Part 11 : Thermoplastics,pipes, fittings and valves, as Method 1111A : 1996, for association with related test,methods for plastics materials and plastics piping components.,This test method has been prepared for reference by other standards under,preparation by CEN for specification of plastics piping systems and components. It has,been implemented to enable experience of the method to be gained and for use for,other fresh applications.,It is also for use for the revision of amendment of other national standards as,practicable, but it should not be presumed to apply to any existing standard or,specification, which contains or makes reference to a different test method, until that,standard has been amended or revised to make reference to this method and any,requirements adjusted as appro……
……